LabMal specialises in online distribution of life science products & services, lab consumables and general lab equipment.
FEATURED PRODUCTS
High-performance silicon anode, 1 micron silicon particles in crosslinked conducting polyanaline matrix – Sigma-Aldrich
RM1,961.00Brand:
Sigma-Aldrich
Synonyms
Doped polyaniline, Si encapsulated in 3D crosslinked polyaniline, Si/PANi composite, Silicon micron particle
General Description
Silicon is a most promising next generation lithium ion battery electrode material, due to its ~10 times higher specific capacity (3600 mAh/g) than graphite (372 mAh/g). However, silicon experiences large volume change (~400%) during lithium insertion, causing it to fracture and detach from current collector, rendering prototypical lithium-silicon batteries to lose most of their capacity in less than 10 charge-discharge cycles. A solution to the capacity and stability issues posed by the significant volume expansion upon lithiation of silicon is critical to the success of high capacity lithium ion batteries.
This silicon/PANi composite utilizes a doped, intrinsically conductive, 3D cross-linked polyaniline as matrix, which could function as both the conductive binder and the polymer electrolyte for silicon-based electrodes. Previous study for a similar silicon-based three-dimensional conducting polymer composite demonstrated increased electrochemically performance due to short diffusion paths and good 3D connectivity, and resulted in a marked improvement in cyclability, with over 90% capacity retention after 5,000 cycles.
This composite is made by encapsulating silicon particles in an in-situ polymerized 3D-crosslinked conductive polyaniline framework. This Si/PANi composite not only allows fast electrical and ionic transport, but also provides free space to allow giant volume expansion. This Si/PANi composite provides a ready-to-use electrochemically active silicon composite that would increase the capacity of conventional lithium ion battery, and improve the cycle-life of Si-based anodes
dATP Solution – 25 umol
RM0.00Brand:
New England Biolabs
Enhance your PCR Reaction with our ultrapure dATP solution
- Compatible with all NEB DNA polymerases in a variety of applications
- ≥ 99% purity as determined by HPLC analysis
- Also available in solution mix (NEB #N0447) or set (NEB #N0446) format
X-VIVO™ 10 Serum-free Hematopoietic Cell Medium, xenofree
RM850.00Brand:
Lonza
Description
The X-VIVO™ 10 Media formulations are designed to support the generation of LAK cells in a serum-free environment. The original protocols involved the incubation of patient or normal donor peripheral blood lymphocytes (PBL) at 1.0 – 3.0 × 106 cells/ml for a period of 3 days in the presence of 1,000 Cetus units of rIL-2/ml. Optimal LAK cell generation is achieved when peripheral blood lymphocytes are incubated for 3 – 10 days at a density of 1.0 – 6.0 × 106 cells/ml in the presence of 100 – 1,000 Cetus units of rIL-2. X-VIVO™ 10 Media is available as a 1X liquid in two convenient formulations.
Key Applications:
-Proliferation of peripheral blood lymphocytes
-Proliferation of tumor infiltrating lymphocytes
-Cryopreservation of human tissue
-Cultivation of human monocytes and macrophages
-Cultivation of stem cells
-Cultivation of dendritic cells
Gallium arsenide (single crystal substrate), <100> – Sigma-Aldrich
RM913.00Brand:
Sigma-Aldrich
Synonyms
Nanofibrous inorganic powder, SiO2
Cas No.
7631-86-9
General Description
Silica nanofibers are yielded through a novel ac electrospinning process resulting in extraordinary aspect ratios, consistent purity, and consistent certification of form parameters that are difficult if not impossible to achieve using other nanofiber production methods. Potential applications include filtration membranes and catalyst support.
Heart Infusion Broth 500g
RM684.00Brand:
Thermo ScientificTM OxoidTM
Oxoid Heart Infusion Broth is a highly nutritious liquid medium recommended for the cultivation of fastidious microorganisms.
Heart Infusion Broth, Oxoid Composition
| Typical Formula* | gm/litre |
| Beef heart infusion solids | 17.5 |
| Proteose peptone | 10.0 |
| Glucose | 2.0 |
| Sodium chloride | 5.0 |
| Di-sodium phosphate | 2.5 |
| pH 7.4 ± 0.2 @ 25°C |
Heart Infusion Broth, Oxoid Preparation:
Dissolve 37g in 1 litre of distilled water. Mix well and distribute into final containers. Sterilise by autoclaving at 121ºC for 15 minutes.
Storage conditions and Shelf life
The dehydrated medium should be stored at 10-30°C and used before the expiry date on the label.
Store the prepared medium in the dark below 20°C.
Precautions
Heart Infusion Broth should only be used for in vitro diagnostic purposes.
Lom10 Lomefloxacin
RM0.00Brand:
Thermo ScientificTM OxoidTM
Poly(3-hexylthiophene-2,5-diyl) – Sigma-Aldrich
RM3,561.00Brand:
Sigma-Aldrich
Synonyms
P3HT
General Description
Poly(3-hexylthiophene) (P3HT) is a regioregular semiconducting polymer. It is used in organic electronics primarily because of its regular end-to-end arrangement of side chain, which allows efficient p- p stacking of the conjugated backbones. On account of the alkyl side group, P3HT is rendered hydrophobic in neutral state. Solution-to-solid phase transformation and thin film formation of poly(3-hexylthiophene) (P3HT) was reported in a study.
Poly(3-hexylthiophene-2,5-diyl) (P3HT) is a poly(alkylthiophene) based semiconducting polymer that is hydrophobic at neutral state and has π-π conjugation in its backbone. It has a hole mobility is in the range of 10-3-10-1 cm2V-1s-1 and is commonly used in the development of field-effect transistors (FETs) for a wide range of applications.
We are committed to bringing you Greener Alternative Products, which adhere to one or more of The 12 Principles of Greener Chemistry. This product belongs to Enabling category of greener alternatives thus aligns with “Design for energy efficency”. Hole transport organic materials allow perfect energy level alignment with the absorber layer and therefore efficient charge collection, are prone to degradation in ambient conditions.
Applications
For the characterization and solid-state properties of this polymer, see J. Am. Chem. Soc. .
P3HT, an electron donor that acts as a semiconducting active layer in combination with an electron acceptor like fullerene derivative (6,6)-phenyl C61-butyric acid methylester (PCBM), can be used to fabricate bulk heterojunction (HJT) based organic solar cells (OSCs).[4][5][6][7] Volatile organic compounds (VOCs) and electric sensor devices can be developed by using Langmuir-Schaefer (LS) films of P3HT and poly(3-octylthiophene)(P3OT). It can also be used with polystyrene to process a nano-scaled polymeric coating through spray coating onto carbon nanotube (CNT) powders.
Poly(3-hexylthiophene-2,5-diyl) may be used to fabricate ZnO nanowire arrays based photodiode. Regio- regular poly(3-hexylthiophene-2,5-diyl) may find extensive use as a semiconducting layer in organic thin film field effect transistor (FETs).
Rechargeable battery electrodes, electrochromic devices, chemical and optical sensors, light-emitting diodes, microelectrical amplifiers, field-effect transistors and non-linear optical materials.
Features & Benefits
Greater than 90% head-to-tail regiospecific conformation.
Good processibility, environmental stability and electroactivity.
PEDOT:PSS, high-conductivity grade, 1.1% aqueous dispersion, surfactant-free – Sigma-Aldrich
RM1,293.00Brand:
Sigma-Aldrich
Synonyms
Orgacon™ ICP 1050, PEDOT:PSS, Poly(2,3-dihydrothieno-1,4-dioxin)-poly(styrenesulfonate)
CAS No
–
General Description
Aqueous surfactant-free dispersion of high conductivity grade PEDOT:PSS polymer. Optimal performance in transparent conductive coatings may require addition of formulation ingredients (e.g. surfactants and high-boiling solvents).Conducting polymer such as poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonate) anions (PEDOT/PSS) is widely used in various organic optoelectronic devices. PEDOT: PSS is a blend of cationic polythiopene derivative, doped with a polyanion. High electrical conductivity and good oxidation resistance of such polymers make it suitable for electromagnetic shielding and noise suppression. Thus, the polymer film was found to possess high transparency throughout the visible light spectrum and even into near IR and near UV regions, virtually 100% absorption from 900-2,000 nm. No absorption maximum from 400-800 nm. Impact of small electric and magnetic fields on the polymer was studied.
Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) is a conductive polymer without a high boiling solvent (HBS), that is formed by electropolymerizing 3,4-ethylenedioxythiophene in a solution of poly(styrenesulfonate) (PSS). PEDOT is doped with positive ions and PSS with negative ions. It has the following properties that make it a viable polymer in organic electronics.
We are committed to bringing you Greener Alternative Products, which adhere to one or more of the 12 Principles of Green Chemistry. This product is used in energy conversion and storage, thus has been enhanced for energy efficiency. Click here for more information.
Applications
PEDOT:PSS can be used as an electrode material with high mobility for charge carriers. It can be used for a wide range of energy based applications such as organic photovoltaics (OPV), perovskite solar cells (DSSCs), organic light emitting diodes (OLEDs) and other biomedical sensors.
Used to prepare highly transparent conductive coating formulations. Primary and secondary nucleation by introducing PEDOT:PSS in a hydrogel was studied.
Virtually 100% absorption from 900-2,000 nm. No absorption maximum from 400-800 nm. Conductive polymer blend.
Legal Information
Product of Agfa-Gevaert N.V.
Orgacon is a trademark of Agfa-Gevaert N.V.
IEF Conversion for 18cm IPG Strips and Tube Gels
RM0.00Brand:
Cleaver Scientific
Conversion for 18cm IPG Strips and Tube Gels for use with CSL-IEF system.
Ampicillin Selective Supplement 1 x 10 Vials
RM479.00Brand:
Thermo ScientificTM OxoidTM
- Oxoid Ampicillin Selective Supplement is used for the isolation of Aeromonas hydrophila.
- Add to to Aeromonas Medium Base, Part No. CM0833B.
Ampicillin Selective Supplement, Oxoid Preparation:
Suspend 29.5g in 500ml of distilled water. Bring gently to the boil. DO NOT AUTOCLAVE. Cool to 50°C and aseptically add one vial of Ampicillin Selective Supplement SR0136 reconsituted as directed. Mix well and pour plates.
| Vial contents (each vial is sufficient for 500 ml of medium) | per vial | per litre |
| Ampicillin |
2.5mg |
5.0mg |
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the prepared plates of medium 2-8°C.
TGT4XMINI Teaching Gel Tank
Brand:
Cleaver Scientific
These industry standard tanks come in three sizes -to run six gels, four gels or a single gel. The gel trays are UV transparent and measure 7x7cm, each tank comes with two combs and two casting dams per gel tray. Supplied with highly flexible cable and connectors which are CE compliant, providing complete electrical isolation and safety. They have a special manufactured safety cover, which completely covers the tank of the system, making it one of the safest available.
abCycler
RM0.00Brand:
AITbiotech
The abCycler offers reliable and accurate PCR system with precise temperature control and rapid temperature ramping. These extensive features coupled with a small footprint are ideal for any laboratories.
Features
Smart design and Convenient features
Reproducibility
Simple, intuitive user interface
Reliability
Please contact us for pricing and availability.
OmniPur Water, WFI Quality, Sterile Purified Water, Cell Culture Tested – CAS7732-18-5, 1L
RM152.00Brand:
Merck
** This product has been discontinued.
OmniPur Water is sterile water that is tested to be DNase free, Protease free, RNase free and bacterial free.
It is suitable to be used in:
- Cell Biology
- Cell culture media preparation, extraction buffer, Molecular work, reconstitute of compound
- Diluent for live cells staining
- Sterile solution preparation Microbiology Sample Preparation
- Diluent and rinsing reagent in Microbial Membrane Filtration
Key Specification:
- Sterile by USP Standard
- DNase, RNase, Protease-Free
- < 500 ppb Total Organic Carbon
- < 0.025 EU/ml Bacterial Endotoxin
Minimum Essential Medium Eagle (EMEM) with Alpha Modification, powder form
Price range: RM395.00 through RM627.00Brand:
Sigma-Aldrich
This is the most enriched variation of the EMEM formulation offered that suitable for cell culuture. It contains all 21 normal amino acids, some at increased concentrations. In addition, it contains 5 additional vitamins. Refer to the table below and choose your preferecd EMEM!
OEM SeaKem® LE Agarose
RM1,514.00Brand:
Lonza
Product Overview
SeaKem® LE Agarose was the first and is still the world’s most trusted agarose for nucleic acid electrophoresis. Ideal for routine analysis of nucleic acids by gel electrophoresis and blotting, each SeaKem® LE Gel sharply resolves DNA and provides consistent resolution from lot-to-lot. This molecular biology grade agarose has no detectable DNase or RNase activity and forms strong gels with low background upon ethidium bromide, SYBR® Green, or GelStarTM Staining. Due to its low EEO, DNA will have a high electrophoretic mobility. SeaKem® LE Agarose is also recommended for protein gel electrophoresis in applications such as Ouchterlony and radial immunodiffusion (RID). Information about bulk and custom packaging is available through Lonza’s Customer Service Team.
Benefits
Applications
Content & Storage
1 kb DNA Ladder, NEB
Brand:
New England Biolabs
This 1 kb DNA ladder is available in Quick-Load Purple format – enjoy the convenience of a ready-to-load format.
1 kb DNA ladder from New England Biolabs (NEB) is suitable for use with molecular weight standard for agarose gel electrophoresis. A number of proprietary plasmids are digested to completion with appropriate restriction enzymes to yield 10 bands, ranging from 0.5 to 10 kilobases. NEB set 3.0 kb fragment as a reference band by increasing the intensity of that band.
- Size range: 500 bp to 10 kb
- Value pricing
- Supplied with a free vial of Gel Loading Dye, Purple (6X), no SDS (NEB #B7025).
- Easy to identify reference bands
- Small size suitable for 200 gel lanes; large size suitable for 1000 gel lanes
Q5 Hot Start High-Fidelity 2X Master Mix
Brand:
New England Biolabs
Fidelity at its finest
Q5® High-Fidelity DNA Polymerase sets a new standard for both fidelity and robust performance. With the highest fidelity amplification available (~280 times higher than Taq), Q5 DNA Polymerase results in ultra-low error rates. Q5 DNA Polymerase is composed of a novel polymerase that is fused to the processivity-enhancing Sso7d DNA binding domain, improving speed, fidelity and reliability of performance.
- Highest fidelity amplification (~280X higher than Taq)
- Ultra-low error rates
- Superior performance for a broad range of amplicons (from high AT to high GC)
- Hot start and master mix formats available
FEATURED PRODUCTS
KAA Agar Base 500g
RM843.00Brand:
Thermo ScientificTM OxoidTM
- Oxoid Kanamycin Aesculin Azide Agar Base is a selective medium for the isolation of Enterococci in foodstuffs.
- Also available Kanamycin Sulphate Selective Supplement, Part No. SR0092E.
Kanamycin Aesculin Azide Agar Base, Oxoid Composition
| Typical Formula* |
gm/litre |
| Tryptone |
18.8 |
| Yeast extract |
5.0 |
| Sodium chloride |
5.0 |
| Sodium citrate |
1.0 |
| Aesculin |
1.0 |
| Ferric ammonium citrate |
0.5 |
| Sodium azide |
0.15 |
| Starch | 0.6 |
| Mix for Streptococci | 0.6 |
| Agar | 10.0 |
| Final pH 7.0 ± 0.2 @ 25°C |
Kanamycin Aesculin Azide Agar, Oxoid Preparation:
Suspend 21.3g in 500ml of distilled water. Add one vial of Kanamycin Supplement (SR0092) reconstituted as directed. Bring to the boil. Sterilise by autoclaving at 121°C for 15 minutes.
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the prepared media at 2-8°C.
Precautions
Observe the hazard precautions regarding sodium azide when disposing of the medium.
There is no universal medium which will isolate all strains of enterococci.
Unless a presumptive count is acceptable all isolates should have their identity confirmed with further tests.
CCDA Selective Supplement 1 x 10 Vials
RM855.00Brand:
Thermo ScientificTM OxoidTM
Oxoid CCDA Selective Supplement is used for the isolation of Campylobacter spp., especially C. upsaliensis or Arcobacter.
- For the isolation of Arcobacter spp., add to Arcobacter Broth Base, Part No. CM0965B
- For the isolation of Campylobacter spp., especially C. upsaliensis, add to Campylobacter Blood-Free Selective Agar Base (CCDA Preston), Part No. CM0739B
CCDA Selective Supplement, Oxoid Composition
| Vial contents (each vial is sufficient for 500ml of medium) |
per vial
|
per litre
|
| Cefoperazone |
16mg |
32mg
|
| Amphotericin B |
5mg |
10mg
|
Campylobacter Blood-Free Selective Agar, Oxoid Preparation:
Suspend 22.75g of Campylobacter Blood-Free Selective Agar Base in 500ml of distilled water and bring to the boil to dissolve. Sterilise by autoclaving at 121°C for 15 minutes. Cool to 50°C. Aseptically add 1 vial of CCDA Selective Supplement SR0155 reconstituted as directed. Mix well and pour into sterile Petri dishes.
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the selective supplement in the dark at 2-8°C and use before the expiry date on the label.
The prepared medium may be stored for up to 2 weeks at 2-8°C .
Brilliance™ UTI 500g
RM0.00Brand:
Thermo ScientificTM OxoidTM
Thermo Scientific™ Oxoid Brilliance™ UTI Agar (formerly Chomogenic UTI Agar ) is a chromogenic medium for the presumptive identification and differentiation of all the main micro-organisms that cause urinary tract infections (UTIs).
Brilliance UTI Agar, Oxoid Composition
| Typical Formula* |
gm/litre |
| Peptone |
15.0 |
| Chromogenic mix |
26.3 |
| Agar |
15.0 |
| Final pH 6.8 ± 0.2 @ 25°C |
Brilliance UTI Agar, Oxoid Preparation:
Suspend 56.3g of Brilliance UTI Agar in 1 litre of distilled water, mix well and sterilise by autoclaving at 121°C for 15 minutes. Cool to 50°C and mix well before pouring plates.
Storage conditions and Shelf life
Dehydrated Brilliance UTI Agar must be stored tightly capped in the original container at 10-30ºC.
Oxoid Brilliance UTI Agar plates should be stored in the original packaging, at the temperature stated on the pack or product specification, and protected from direct light.
When stored as directed, the unopened product will remain stable until the expiry date on the label. Locally prepared media can be stored for up to 2 weeks when made from CM0949 according to the manufacturer’s instructions and stored at 2-8ºC, in the dark. A longer shelf life may be attainable, but should be validated under the relevant, local manufacturing and storage conditions.
Buffered oxide etchant (BOE) 10:1 – Sigma-Aldrich
RM660.00Brand:
Sigma-Aldrich
Synonyms
BHF, Buffered HF
Cas No.
–
General Descriptions
Buffered oxide etchant (BOE) is a wet etchant used in microfabrication. Its primary use is in etching thin films of silicon dioxide (SiO2) or silicon nitride (Si3N4). It is a mixture of a buffering agent, such as ammonium fluoride (NH4F), and hydrofluoric acid (HF). Concentrated HF etches silicon dioxide too quickly for good process control and also peels the photoresist used in lithographic patterning.
Application
Buffered oxide etchant (BOE) 10:1 can be used in the etching of titanium carbide, which can be used in microelectromechanical systems (MEMS). It can also be used in the etching of spin-on-dopant (SOD) for the development of conductor-insulator-conductor tunnelling diodes. It can also be used to enhance the surface of fused quartz devices.
Clostridium Difficile Selective Supplement 1 x 10 Vials
RM1,673.00Brand:
Thermo ScientificTM OxoidTM
- Oxoid Clostridium Difficile Selective Supplement is added to Clostridium Difficile Agar Base, Part No. CM0601B.
- Each vial supplements 500mL of medium.
Clostridium Difficile Selective Supplement, Oxoid Composition
| Vial contents (each vial is sufficient for 500mls of medium) |
per vial
|
per litre
|
| D-cycloserine |
125.0mg
|
250.0mg |
| Cefoxitin |
4.0mg
|
8.0mg |
Clostridium Difficile Agar, Oxoid Preparation:
Suspend 34.5g in 500ml of distilled water and bring gently to the boil to dissolve completely. Sterilise by autoclaving at 121°C for 15 minutes. Allow to cool to 50°C and add aseptically the contents of 1 vial of Oxoid Clostridium Difficile Supplement (SR0096) reconstituted as directed, together with 7% (v/v) Defibrinated Horse Blood (SR0050). Sheep Blood (SR0051) may be used in place of Horse Blood but some strains of the organism will show a slightly reduced growth recovery. Mix well and pour into sterile Petri dishes.
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the prepared medium at 2-8°C no longer than 5-7 days.
Tinsdale Medium 500g
RM0.00Brand:
Thermo ScientificTM OxoidTM
Oxoid Tinsdale Agar Base is used for the isolation and identification of Corynebacterium diphtheriae.
Tinsdale Agar Base, Oxoid Composition
| Typical Formula* |
gm/litre
|
| Proteose peptone |
20.0 |
| Yeast extract |
5.0 |
| Sodium chloride |
5.0 |
| L-cystine |
0.24 |
| Agar |
15.0
|
| pH 7.9 ± 0.2 @ 25°C |
Tinsdale Agar, Oxoid Preparation:
Suspend 9g of agar base in 200ml of distilled water. Bring to the boil and dissolve completely. DO NOT AUTOCLAVE. Allow to cool to approximately 50°C and add the contents of one vial of Oxoid Tinsdale Supplement SR0065 reconstiuted as directed. Mix throughly and pour into sterile Petri dishes.
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the prepared medium at 2-8°C for not more than 4 days.
Precautions
Further tests must be carried out on colonies suspected as Corynebacterium diphtheriae, including cell morphology after sub-culture to Loeffler’s Medium and examination for toxin production.
Do not incubate Tinsdale’s Agar plates in enhanced CO2 atmosphere (5-10% v/v).
N,N-Dimethylacetamide, ReagentPlus®, 99% (Sigma-Aldrich)
RM843.00Brand:
Sigma-Aldrich
General Description
CAS number: 127-19-5
Chemical Formula: CH3CON(CH3)2
Molar Mass: 87.12 g/mol
50 bp DNA Ladder, NEB
Brand:
New England Biolabs
This product is available in our Quick-Load Purple format – enjoy the convenience of a ready-to-load format.
- Size range: 50 bp – 1350 bp
- Supplied with a free vial of Gel Loading Dye, Purple (6X), no SDS (NEB #B7025)
- Easy-to-identify reference bands
- Small size suitable for 200 gel lanes; large size suitable for 1000 gel lanes
PEDOT:PSS, high-conductivity grade, 3.0-4.0% aqueous dispersion – Sigma-Aldrich
Price range: RM297.00 through RM1,187.00Brand:
Sigma-Aldrich
Synonyms
PEDOT:PSS, Poly(2,3-dihydrothieno-1,4-dioxin)-poly(styrenesulfonate)
CAS No
–
General Description
Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) is an organic semiconductor prepared by doping cationic poly(3,4-ethylenedioxythiophene) and poly(4-styrenesulfonate) anion. Its high electrical conductivity and good oxidation resistance make it suitable for electromagnetic shielding and noise suppression. PEDOT:PSS based polymeric films have a high transparency throughout the visible light spectrum and even in near IR and near UV regions, with virtually 100% absorption from 900-2000 nm. PEDOT provides the conduction properties and PSS forms a hydrated colloidal solution.
We are committed to bringing you Greener Alternative Products, which adhere to one or more of the 12 Principles of Green Chemistry. This product is used in energy conversion and storage, thus has been enhanced for energy efficiency. Click here for more information.
Applications
Electrical conductivity measurements herewith reported were on a film deposited by spin-coating on a clean glass, then dried (130 °C for 15 minutes on a hotplate). The layer thickness was determined by scratching the layer and measuring the profile/height of the scratch by a stylus profilometer. Electrodes for the measurement were by evaporating metal contacts (four-point probes).
PEDOT:PSS is an intrinsically conductive polymer (ICP) that can be coated on various substrates and nanostructures like fullerenes (C60) to form composites with high electrochemical properties for applications like low-cost printed electronics, optoelectronics, and polymeric solar cells. It can be used as a conductive hydrogel with polyethylene glycol-diacrylate (PEG-DA) for potential applications in tissue engineering. PEDOT:PSS also finds use in other organic electronic applications like organic thin film transistors (OTFTs) and dye sensitized solar cells (DSSCs).
Ready-to-use high conductivity coating formulation.
Virtually 100% absorption from 900-2,000 nm. No absorption maximum from 400-800 nm. Conductive polymer blend.
Packaging
Packaged in poly bottles
E10 Erythromycin
RM0.00Brand:
Thermo ScientificTM OxoidTM
Gentamycin 1024 M.I.C.E. (10 Pack)
RM0.00Brand:
Thermo ScientificTM OxoidTM
**This product is not available at the moment.
Effortlessly establish accurate Minimum Inhibitory Concentration (MIC) values manually using Thermo Scientific™ Oxoid™ Gentamycin M.I.C.Evaluator Strips (M.I.C.E.™).
Tryptone Soya Broth (acc. to EP/USP)
RM336.00Brand:
Thermo ScientificTM OxoidTM
Thermo Scientific™ Oxoid Tryptone Soya Broth is tested according to EP/USP.
Tryptone Soya Broth, Oxoid Composition
| Formula |
gm/litre |
| Pancreatic digest of casein |
17.0 |
| Enzymatic digest of soya bean* |
3.0 |
| Sodium chloride |
5.0 |
| Dipotassium hydrogen phosphate |
2.5 |
| Glucose |
2.5 |
| pH 7.3 ± 0.2 @ 25°C |
*Contains papain
Tryptone Soya Broth, Oxoid Preparation:
Add 30g to 1 litre of water (purified as required), mix well and distribute into final containers. Sterilise by autoclaving at 121°C for 15 minutes.
Storage conditions and Shelf life
Store the dehydrated medium at 10-30°C and use before the expiry date on the label.
Store the prepared medium away form the light at room temperature.
OmniPur Water, WFI Quality, Sterile Purified Water, Cell Culture Tested – CAS7732-18-5, 1L
RM152.00Brand:
Merck
** This product has been discontinued.
OmniPur Water is sterile water that is tested to be DNase free, Protease free, RNase free and bacterial free.
It is suitable to be used in:
- Cell Biology
- Cell culture media preparation, extraction buffer, Molecular work, reconstitute of compound
- Diluent for live cells staining
- Sterile solution preparation Microbiology Sample Preparation
- Diluent and rinsing reagent in Microbial Membrane Filtration
Key Specification:
- Sterile by USP Standard
- DNase, RNase, Protease-Free
- < 500 ppb Total Organic Carbon
- < 0.025 EU/ml Bacterial Endotoxin
Minimum Essential Medium Eagle (EMEM) with Alpha Modification, powder form
Price range: RM395.00 through RM627.00Brand:
Sigma-Aldrich
This is the most enriched variation of the EMEM formulation offered that suitable for cell culuture. It contains all 21 normal amino acids, some at increased concentrations. In addition, it contains 5 additional vitamins. Refer to the table below and choose your preferecd EMEM!
OEM SeaKem® LE Agarose
RM1,514.00Brand:
Lonza
Product Overview
SeaKem® LE Agarose was the first and is still the world’s most trusted agarose for nucleic acid electrophoresis. Ideal for routine analysis of nucleic acids by gel electrophoresis and blotting, each SeaKem® LE Gel sharply resolves DNA and provides consistent resolution from lot-to-lot. This molecular biology grade agarose has no detectable DNase or RNase activity and forms strong gels with low background upon ethidium bromide, SYBR® Green, or GelStarTM Staining. Due to its low EEO, DNA will have a high electrophoretic mobility. SeaKem® LE Agarose is also recommended for protein gel electrophoresis in applications such as Ouchterlony and radial immunodiffusion (RID). Information about bulk and custom packaging is available through Lonza’s Customer Service Team.
Benefits
Applications
Content & Storage
1 kb DNA Ladder, NEB
Brand:
New England Biolabs
This 1 kb DNA ladder is available in Quick-Load Purple format – enjoy the convenience of a ready-to-load format.
1 kb DNA ladder from New England Biolabs (NEB) is suitable for use with molecular weight standard for agarose gel electrophoresis. A number of proprietary plasmids are digested to completion with appropriate restriction enzymes to yield 10 bands, ranging from 0.5 to 10 kilobases. NEB set 3.0 kb fragment as a reference band by increasing the intensity of that band.
- Size range: 500 bp to 10 kb
- Value pricing
- Supplied with a free vial of Gel Loading Dye, Purple (6X), no SDS (NEB #B7025).
- Easy to identify reference bands
- Small size suitable for 200 gel lanes; large size suitable for 1000 gel lanes
Q5 Hot Start High-Fidelity 2X Master Mix
Brand:
New England Biolabs
Fidelity at its finest
Q5® High-Fidelity DNA Polymerase sets a new standard for both fidelity and robust performance. With the highest fidelity amplification available (~280 times higher than Taq), Q5 DNA Polymerase results in ultra-low error rates. Q5 DNA Polymerase is composed of a novel polymerase that is fused to the processivity-enhancing Sso7d DNA binding domain, improving speed, fidelity and reliability of performance.
- Highest fidelity amplification (~280X higher than Taq)
- Ultra-low error rates
- Superior performance for a broad range of amplicons (from high AT to high GC)
- Hot start and master mix formats available
PRODUCT CATEGORIES
OUR BRANDS
DISTRIBUTION PARTNERS
LabMal is the online distribution of life science and biotechnology products, including microbiology, molecular biology, cell biology, general lab equipment, plastic consumables, chemical, cleansing solution and protein. If you are interested in the products from our distribution partners that are not available in Labmal, please contact us at 03-8051 5106 or info@labmal.com.
